Improvement on room-temperature ductility of 6.5 wt.% Si steel by stress-relief annealing treatments after warm rolling
X Wang, W Zhang, Z Liu, H Li, G Wang - Materials Characterization, 2016 - Elsevier
In our previous work, we demonstrated that thin sheets of 6.5 wt.% Si steel could be
fabricated by cold rolling with deformation induced disordering (DID). However, because the …
fabricated by cold rolling with deformation induced disordering (DID). However, because the …
Effect of Si on mechanical property of galvannealed dual phase steel
S Hironaka, H Tanaka, T Matsumoto - Materials Science Forum, 2010 - Trans Tech Publ
The mechanical properties of galvannealed dual phase steels bearing Si were investigated,
and then the effect of Si on work hardening behavior during tensile deformation was …
and then the effect of Si on work hardening behavior during tensile deformation was …
Room-temperature quenching and partitioning steel
The current study proposes a room-temperature quenching and partitioning (RT-Q&P)
process to design new steels with an ultrahigh tensile strength (1.3~ 1.5 GPa) and a large …
process to design new steels with an ultrahigh tensile strength (1.3~ 1.5 GPa) and a large …
Effects of isothermal transformation conditions on the microstructure and hardness values of a high-carbon Al–Si alloyed steel
S Baradari, SMA Boutorabi - Materials & Design, 2015 - Elsevier
In this investigation, the microstructure and hardness of a high-strength high-carbon steel
containing 0.80 wt.% silicon and 0.84 wt.% aluminum have been evaluated under different …
containing 0.80 wt.% silicon and 0.84 wt.% aluminum have been evaluated under different …
[HTML][HTML] Research status and development prospect of Fe–Mn–C–Al system low-density steels
S Bai, Y Chen, X Liu, H Lu, P Bai, D Li, Z Huang… - Journal of Materials …, 2023 - Elsevier
The rapid development of automotive industry results in a series of increasingly serious
problems such as energy consumption and environmental pollution, so that developing the …
problems such as energy consumption and environmental pollution, so that developing the …
Alloy design by dislocation engineering
Ultra-high strength alloys with good ductility are ideal materials for lightweight structural
application in various industries. However, improving the strength of alloys frequently results …
application in various industries. However, improving the strength of alloys frequently results …
Effect of retained austenite on the fracture behavior of a novel press-hardened steel
Tensile and bending properties are two critical attributes of press hardened steels (PHSs) for
automotive body structural components. However, the research on these properties of PHSs …
automotive body structural components. However, the research on these properties of PHSs …
Microstructure and mechanical properties of C–Mn–Al–Si hot-rolled TRIP steels with and without Nb based on dynamic transformation
B Fu, WY Yang, MY Lu, Q Feng, LF Li… - Materials Science and …, 2012 - Elsevier
Two C–Mn–Al–Si TRIP steels with and without 0.038 (wt)% Nb addition were fabricated by a
thermo-mechanical process based on dynamic transformation of undercooled austenite …
thermo-mechanical process based on dynamic transformation of undercooled austenite …
Recrystallization behavior in a low-density high-Mn high-Al austenitic steel undergone thin strip casting process
The recrystallization behavior of a high-Mn high-Al lightweight steel (Fe-28.4 Mn-8.3 Al-1.27
C (wt%)) with 50% cold rolling deformation is investigated at the annealing temperature of …
C (wt%)) with 50% cold rolling deformation is investigated at the annealing temperature of …
Ultra-high strength steel made from AISI 304L using a novel thermo-mechanical processing technique
Presented here is a technique of producing an ultra-high strength steel starting with an
annealed low strength AISI 304L stainless steel. Annealed AISI 304L stainless steel was …
annealed low strength AISI 304L stainless steel. Annealed AISI 304L stainless steel was …