A new hot-rolled lightweight steel with ultra-high strength and good ductility designed by dislocation character and transformation strain

C Song, H Wang, Z Sun, J Xu, H Chen, W Yin - Scripta Materialia, 2022 - Elsevier
The method of Si substituting for Al was proposed to design a novel hot-rolled lightweight
steel with ultra-high ultimate tensile strength (2046 MPa) and good total elongation after …

Novel ultra-high-strength (ferrite+ austenite) duplex lightweight steels achieved by fine dislocation substructures (Taylor lattices), grain refinement, and partial …

SS Sohn, H Song, BC Suh, JH Kwak, BJ Lee, NJ Kim… - Acta Materialia, 2015 - Elsevier
Weight reduction from down-gauged high-strength steels has been an important issue in
automotive industries to improve fuel efficiency. In addition to lightweight needs, automotive …

Processing of a new high strength high toughness steel with duplex microstructure (Ferrite+ Austenite)

CJ Martis, SK Putatunda, J Boileau - Materials & Design (1980-2015), 2013 - Elsevier
In this investigation a new third generation advanced high strength steel (AHSS) has been
developed. This steel was synthesized by austempering of a low carbon and low alloy steel …

Microstructure and mechanical proper-ties of Fe-Mn-Al light-weight high strength steel

F YANG, R SONG, T SUN, L ZHANG, C ZHAO, B LIAO - Acta Metall Sin, 2014 - ams.org.cn
The automobile industry pays lots of attention on a new kind of steel with excellent
combination of strength and ductility as well as the lower density, aiming at developing more …

Novel ferrite–austenite duplex lightweight steel with 77% ductility by transformation induced plasticity and twinning induced plasticity mechanisms

SS Sohn, K Choi, JH Kwak, NJ Kim, S Lee - Acta Materialia, 2014 - Elsevier
The need for lightweight materials has been an important issue in automotive industries to
reduce greenhouse gas emission and to improve fuel efficiency. In addition, automotive …

Achievement of high yield strength and strain hardening rate by forming fine ferrite and dislocation substructures in duplex lightweight steel

H Song, J Yoo, SS Sohn, M Koo, S Lee - Materials Science and …, 2017 - Elsevier
Lightweight steels containing a considerable content of Al show high specific strength and
ductility, but there are some drawbacks such as low yield strength and stringer-type bands …

An ultrahigh strength and enhanced ductility cold-rolled medium-Mn steel treated by intercritical annealing

X Li, R Song, N Zhou, J Li - Scripta Materialia, 2018 - Elsevier
An ultrahigh strength and enhanced ductility cold-rolled medium-Mn steel was manufactured
via intercritical annealing. The fine lamellar and equiaxed duplex microstructure, austenite …

Super-strong dislocation-structured high-carbon martensite steel

J Sun, Y Liu, Y Zhu, F Lian, H Liu, T Jiang, S Guo… - Scientific reports, 2017 - nature.com
High-carbon martensite steels (with C> 0.5 wt.%) are very hard but at the same time as brittle
as glass in as-quenched or low-temperature-tempered state. Such extreme brittleness …

[HTML][HTML] Achieving ultrahigh strength by tuning the hierarchical structure of low-carbon martensitic steel

B Gao, L Wang, Y Liu, J Liu, L Xiao, Y Sui… - Materials Science and …, 2023 - Elsevier
The high strength of martensitic steel can be attributed to its fine hierarchical structure and
high dislocation density. To further improve the mechanical properties of low-carbon …

Design considerations for the third generation advanced high strength steel

PJ Gibbs - 2012-Mines Theses & Dissertations, 2012 - repository.mines.edu
Advanced high strength steels containing metastable austenite are of considerable interest
due to the combinations of strength and ductility that are achieved via austenite …