Roles of surface coverage increase and re-peening on properties of AISI 1045 carbon steel in conventional and severe shot peening processes
Surface coverage as one of the most effective parameters of shot peening process has
substantial influence on the functionality of the peened component. The aim of this study is …
substantial influence on the functionality of the peened component. The aim of this study is …
Investigation on surface layer characteristics of shot peened graphene reinforced Al composite by X-ray diffraction method
Graphene reinforced Al composite with high mechanical property was successfully reported.
However, there are quite limited studies about shot peening effect on this new type material …
However, there are quite limited studies about shot peening effect on this new type material …
Effect of surface self-nanocrystallization on diffusion bonding between a titanium alloy and a TiAl-based alloy
X Fu, X Wang, Q Wang, W Zhou, H Xu, D Liu… - Journal of Materials …, 2018 - Springer
A self-nanocrystallization layer was prepared on the surface of a Ti alloy sample via shot
peening to investigate its influence on the follow-up diffusion bonding between a titanium …
peening to investigate its influence on the follow-up diffusion bonding between a titanium …
[PDF][PDF] 喷丸时间对GH4169 合金表层组织及性能的影响
郭胜华， 郑海忠， 程世平， 舒小勇， 李贵发 - 特种铸造及有色合金, 2018 - qikan.cmes.org
摘要利用2 mm 不锈钢弹丸对GH4169 合金表面进行高能喷丸处理, 研究喷丸时间对合金表面形
貌, 表层显微组织, 表面粗糙度和显微硬度的影响. 结果表明, 随着喷丸时间延长 …
貌, 表层显微组织, 表面粗糙度和显微硬度的影响. 结果表明, 随着喷丸时间延长 …
Effects of Laser Shock Processing on Impact Toughness of Ti-17 Titanium Alloy
S Huang, Y Zhu, W Guo, P Peng… - … Temperature Materials and …, 2018 - degruyter.com
Ti-17 titanium alloy was treated with laser shock processing (LSP) and tested for impact
toughness. Residual compressive stress, cross-section hardness, microstructure, and the …
toughness. Residual compressive stress, cross-section hardness, microstructure, and the …
Effect of surface nanocrystallization on corrosion behaviour of coated steel in chloride solution
L Zhang, S Yang, H Wu, X Jie, X Huang… - International Journal of …, 2018 - Elsevier
A nanocrystalline (NC) layer was fabricated on the surface of the low-alloy steel 15CrMo
using high-energy shot peening. Two kinds of conversion coatings including the chemical …
using high-energy shot peening. Two kinds of conversion coatings including the chemical …
[PDF][PDF] Effects of shot peening time on microstructure and properties of GH4169 alloy surface
郭胜华， 郑海忠， 程世平， 舒小勇… - Special Casting & …, 2018 - qikan.cmes.org
High energy shot peening was used to treat the surface of GH4169 alloy with 2mm in
diameter stainless steel projectile. The effects of different shot peening time (1min, 3min …
diameter stainless steel projectile. The effects of different shot peening time (1min, 3min …
Gradient Material Fabricated via Accumulative Skin Pass Rolling and Related Microstructure and Mechanical Characterization
D Luo - 2018 - ro.uow.edu.au
Significant efforts have been made in recent years to improve the ductility of ultra-fine
grained/nanograined (UFG/NG) materials while preserving their high strength. Fabricating …
grained/nanograined (UFG/NG) materials while preserving their high strength. Fabricating …