Tribological behavior of plasma sprayed Al2O3-based cermet coatings
V Fervel, B Normand, C Coddet - Wear, 1999 - Elsevier
The study of the tribological behavior of plasma sprayed coatings (Al2O3, Al2O3/TiO2,
Al2O3/TiO2/Copper) in dry conditions was carried out in a cylinder/plane configuration. The …
Al2O3/TiO2/Copper) in dry conditions was carried out in a cylinder/plane configuration. The …
Influence of secondary electro-conductive phases on the electrical discharge machinability and frictional behavior of ZrO2-based ceramic composites
K Bonny, P De Baets, J Vleugels, A Salehi… - journal of materials …, 2008 - Elsevier
ZrO2-based composites with 40vol.% WC, TiCN or TiN were processed in order to
investigate the wire electrical discharge machining (EDM) possibility in demineralised water …
investigate the wire electrical discharge machining (EDM) possibility in demineralised water …
Influence of electrical discharge machining on tribological behavior of ZrO2–TiN composites
K Bonny, P De Baets, J Vleugels, A Salehi… - Wear, 2008 - Elsevier
ZrO2-based composites containing electro-conductive secondary phases have successfully
proven their feasibility for electrical discharge machining (EDM) in demineralised water …
proven their feasibility for electrical discharge machining (EDM) in demineralised water …
Microscopic investigation on the origin of wear by surface fatigue in dry sliding
M Terheci - Materials characterization, 2000 - Elsevier
Simple statistics and morphological analysis in conjunction with the general theory of
surface fatigue were used to determine the origin (s) of the mechanisms of wear by surface …
surface fatigue were used to determine the origin (s) of the mechanisms of wear by surface …
Grain boundary and testing procedure: a new approach to the tribology of alumina materials
M Terheci - Wear, 1997 - Elsevier
In this study the wear behaviour of three grades of alumina ceramic material was
investigated. The experimental procedure was found to influence the accuracy of data …
investigated. The experimental procedure was found to influence the accuracy of data …
Self-lubrication by formation of graphite films in the sliding of silicon nitride against cast iron
Self-lubrication by the formation of a graphite film was studied for the sliding pair of silicon
nitride/cast iron using a ball-on-disk tribomeier. In these experiments, the normal load and …
nitride/cast iron using a ball-on-disk tribomeier. In these experiments, the normal load and …
Impact of Wire-EDM on Tribological Characteristics of ZrO2-based Composites in Dry Sliding Contact with WC–Co-Cemented Carbide
K Bonny, Y Perez Delgado, P De Baets, J Sukumaran… - Tribology Letters, 2011 - Springer
The effect of surface conditions and secondary phase addition on the dry sliding friction and
wear characteristics of five yttria-stabilized ZrO 2-based composites with 40 vol% WC, TiCN …
wear characteristics of five yttria-stabilized ZrO 2-based composites with 40 vol% WC, TiCN …
SiC 与ZrO_2 摩擦副疲劳磨损的有限元分析
田晓， 王翠表， 祝彦 - 润滑与密封, 2009 - cqvip.com
对SiC 与ZrO2 陶瓷组成的销盘式摩擦副摩擦过程中的疲劳磨损现象进行了理论分析,
采用ANSYS 有限元分析软件对其磨损过程中的应力分布进行了分析. 结果表明 …
采用ANSYS 有限元分析软件对其磨损过程中的应力分布进行了分析. 结果表明 …
Wear by surface fatigue on a new foundation Part II. Particle detachment mechanisms and quantitative aspects
M Terheci - Wear, 1998 - Elsevier
An alternative model of wear produced by surface fatigue (SFW) was suggested. Surface
cracks control the process of wear particle generation by SFW. New models of contact …
cracks control the process of wear particle generation by SFW. New models of contact …
Friction and Wear Characteristics of SiC and Si3N4 Ceramics Against ZrO2 Ceramic under Dry Friction
X Tian, B Lin, WL Zhang - Key Engineering Materials, 2004 - Trans Tech Publ
The friction and wear of the silicon carbide (SiC) and hot pressed silicon nitride (Si3N4)
against zirconia (Y–TZP) sliding under dry friction and room temperature conditions were …
against zirconia (Y–TZP) sliding under dry friction and room temperature conditions were …