Metallic biomaterials for medical implant applications: a review
Stainless steel, titanium alloys and cobalt chromium molybdenum alloys are classified under
the metallic biomaterials whereby various surgical implants, prosthesis and medical devices …
the metallic biomaterials whereby various surgical implants, prosthesis and medical devices …
Superplasticity in an organic crystal
S Takamizawa, Y Takasaki, T Sasaki… - Nature Communications, 2018 - nature.com
Superplasticity, which enables processing on hard-to-work solids, has been recognized only
in metallic solids. While metallic materials and plastics (polymer solids) essentially possess …
in metallic solids. While metallic materials and plastics (polymer solids) essentially possess …
Ultra-grain refinement and enhanced low-temperature superplasticity in a friction stir-processed Ti-6Al-4V alloy
W Zhang, H Ding, M Cai, W Yang, J Li - Materials Science and Engineering …, 2018 - Elsevier
An ultrafine microstructure consisting of α grains (~ 0.51 µm) and a small amount of β phase
was successfully achieved in a friction stir-processed (FSPed) Ti-6Al-4V alloy. The fraction of …
was successfully achieved in a friction stir-processed (FSPed) Ti-6Al-4V alloy. The fraction of …
Effect of texture and mechanical anisotropy on flow behaviour in Ti–6Al–4V alloy under superplastic forming conditions
L Da Silva, G Sivaswamy, L Sun, S Rahimi - Materials Science and …, 2021 - Elsevier
The dependency of anisotropic flow behaviour on crystallographic texture is investigated in
Ti–6Al–4V alloy at 750° C and 900° C under constant strain rates of 10− 2, 10− 3 and 2× …
Ti–6Al–4V alloy at 750° C and 900° C under constant strain rates of 10− 2, 10− 3 and 2× …
Intermetallic formation and mechanical properties of Ni-Ti diffusion couples
L Hu, Y Xue, F Shi - Materials & Design, 2017 - Elsevier
Abstract Samples of Ni-Ti diffusion couples were prepared by hot pressing in a furnace with
a vacuum of 10− 1 Pa. Scanning electron microscopy (SEM) investigations indicated that …
a vacuum of 10− 1 Pa. Scanning electron microscopy (SEM) investigations indicated that …
Studies on titanium alloys for aerospace application
A Gomez-Gallegos, P Mandal, D Gonzalez… - Defect and Diffusion …, 2018 - Trans Tech Publ
Since the development of the Ti54M titanium alloy in 2003, its application within the
aerospace sector has gradually increased due to the combination of properties such as …
aerospace sector has gradually increased due to the combination of properties such as …
[HTML][HTML] Effect of laser peen forming process parameters on bending and surface quality of Ti-6Al-4V sheets
Laser peen forming (LPF) is a metal forming process that utilizes laser-induced mechanical
shock waves to form desired shapes or modify bent structures. The present work focuses on …
shock waves to form desired shapes or modify bent structures. The present work focuses on …
Initial microstructure influence on Ti–Al–Mo–V alloy's superplastic deformation behavior and deformation mechanisms
Superplastic forming is an effective way to manufacture complex-shaped parts of titanium-
based alloys. This paper studies the influence of the initial microstructure and its strain …
based alloys. This paper studies the influence of the initial microstructure and its strain …
Superplastic forming of shells from sheet blanks with thermally unstable coatings
The article is devoted to superplastic forming of non-uniformly heated sheet blanks from
aluminum alloy AMg6M. To create an uneven temperature field over the surface of the blank …
aluminum alloy AMg6M. To create an uneven temperature field over the surface of the blank …
Deformation mechanisms during superplastic testing of Ti–6Al–4V–0.1 B alloy
Superplastic tensile tests on warm rolled and optimally annealed boron modified alloy Ti–
6Al–4V–0.1 B at a temperature of 850° C and initial strain rate of 3× 10− 4s− 1 results in a …
6Al–4V–0.1 B at a temperature of 850° C and initial strain rate of 3× 10− 4s− 1 results in a …