An overview of technological parameter optimization in the case of laser cladding
K Wang, W Liu, Y Hong, HMS Sohan, Y Tong, Y Hu… - Coatings, 2023 - mdpi.com
This review examines the methods used to optimize the process parameters of laser
cladding, including traditional optimization algorithms such as single-factor, regression …
cladding, including traditional optimization algorithms such as single-factor, regression …
Gradient descent-particle swarm optimization based deep neural network predictive control of pressurized water reactor power
DA Ejigu, X Liu - Progress in Nuclear Energy, 2022 - Elsevier
A pressurized water reactor (PWR) is an integrated system of various interdependent
subsystems that show highly nonlinear behavior, and each component is prone to …
subsystems that show highly nonlinear behavior, and each component is prone to …
Intelligent fault diagnosis of hydraulic piston pump combining improved LeNet-5 and PSO hyperparameter optimization
Y Zhu, G Li, R Wang, S Tang, H Su, K Cao - Applied Acoustics, 2021 - Elsevier
The hydraulic axial piston pump is the power heart of the hydraulic transmission system in
aerospace equipment and industrial filed. Its stable operation will directly affect the safety …
aerospace equipment and industrial filed. Its stable operation will directly affect the safety …
Trajectory control of electro-hydraulic position servo system using improved PSO-PID controller
H Feng, W Ma, C Yin, D Cao - Automation in Construction, 2021 - Elsevier
This paper presents an improved particle swarm optimization (PSO) algorithm to optimize
the coefficients of the proportional integral derivative (PID) controller for trajectory tracking …
the coefficients of the proportional integral derivative (PID) controller for trajectory tracking …
Revealing the hot deformation behavior of AZ42 Mg alloy by using 3D hot processing map based on a novel NGO-ANN model
The hot deformation behavior of AZ42 alloy was observed using thermal compression tests
at a temperature scope of 250–400° C and strain rate scope of 0.001–1 s− 1. True stress …
at a temperature scope of 250–400° C and strain rate scope of 0.001–1 s− 1. True stress …
Modeling and optimization method of laser cladding based on GA-ACO-RFR and GNSGA-II
Laser cladding is an environmentally friendly and reliable surface modification technology.
The quality characteristics of the coating are directly affected by the process parameters of …
The quality characteristics of the coating are directly affected by the process parameters of …
Shear strength estimation of reinforced concrete walls using support vector regression improved by Teaching–learning-based optimization, Particle Swarm …
P Parsa, H Naderpour - Journal of Building Engineering, 2021 - Elsevier
Peak shear strength estimation of RC shear walls is one of the influential parameters on the
design of RC shear walls. Considering all models and equations provided by researchers …
design of RC shear walls. Considering all models and equations provided by researchers …
Intelligent numerical computing paradigm for heat transfer effects in a Bodewadt flow
The current research article is intended to examine the nonlinear input-output fitting with two-
layer feed forward neural network for numerical treatment of heat transfer effects in …
layer feed forward neural network for numerical treatment of heat transfer effects in …
CNN-BiLSTM enabled prediction on molten pool width for thin-walled part fabrication using Laser Directed Energy Deposition
Abstract Laser Directed Energy Deposition (LDED) is a promising metal Additive
Manufacturing (AM) technology capable of fabricating thin-walled parts to support some high …
Manufacturing (AM) technology capable of fabricating thin-walled parts to support some high …
[HTML][HTML] Constitutive model research on the hot deformation behavior of Ti6Al4V alloy under wide temperatures
The hot compression tests of Ti6Al4V alloy were carried out at different temperatures (500,
600, 700, 800, and 900° C) and different strain rates (0.01 s− 1, 0.1 s− 1, and 1 s− 1). The …
600, 700, 800, and 900° C) and different strain rates (0.01 s− 1, 0.1 s− 1, and 1 s− 1). The …