Dry sliding wear behaviour of in situ Al–TiB2 composites
K Niranjan, PR Lakshminarayanan - Materials & Design, 2013 - Elsevier
Aluminium matrix/titanium diboride reinforced (Al/TiB2) composites were fabricated by in situ
process. The wear behaviour was studied by using a pin-on-disc wear tester at room …
process. The wear behaviour was studied by using a pin-on-disc wear tester at room …
Developing partially oxidized NiCr coatings using the combined flame spray and plasma spray process for improved wear behaviour at high temperature
The powders of NiCrBSiFe and NiCr are partially oxidized using a flame spray process and
are deposited on MDN321 steel substrate using a plasma spray process. The effect of partial …
are deposited on MDN321 steel substrate using a plasma spray process. The effect of partial …
Effect of sintering parameters on densification, corrosion and wear behaviour of Ni-50Fe alloy prepared by spark plasma sintering
MI Makena, MB Shongwe, MM Ramakokovhu… - Journal of Alloys and …, 2017 - Elsevier
Spark plasma sintering (SPS) technique was used to fabricate Ni50Fe alloys. Powders were
sintered at various temperatures, pressure and holding times ranging between 900 and …
sintered at various temperatures, pressure and holding times ranging between 900 and …
Microstructural charactistics of plasma sprayed NiCrBSi coatings and their wear and corrosion behaviors
S Huang, J Zhou, K Sun, H Yang, W Cai, Y Liu, P Zhou… - Coatings, 2021 - mdpi.com
Nickel-based alloys are commonly used as protective coating materials for surface
protection applications owing to their superior resistance to corrosion, wear and high …
protection applications owing to their superior resistance to corrosion, wear and high …
Differentiation of specific wear rates of AISI 304 austenitic and AISI 2205 duplex stainless steels at room and high temperatures
DA Ahmed, MM Mulapeer - Heliyon, 2022 - cell.com
Austenitic and duplex stainless steels are used in numerous applications at room and high
temperatures. However, their wear behaviour at high temperatures has not yet been …
temperatures. However, their wear behaviour at high temperatures has not yet been …
Effect of strain hardening on wear and corrosion resistance of 316L Austenitic stainless steel
G Sun, J Huang, J Peng, W Wu - Journal of Materials Engineering and …, 2024 - Springer
The wear and corrosion resistance of 316L austenitic stainless steel after strain hardening
were studied. 316L austenitic stainless steel was composed of a large amount of austenite …
were studied. 316L austenitic stainless steel was composed of a large amount of austenite …
Thermal spray coatings for blast furnace tuyere application
A Pathak, G Sivakumar, D Prusty, J Shalini… - Journal of Thermal …, 2015 - Springer
The components in an integrated steel plant are invariably exposed to harsh working
environments involving exposure to high temperatures, corrosive gases, and erosion/wear …
environments involving exposure to high temperatures, corrosive gases, and erosion/wear …
[PDF][PDF] Comparison of specific wear rates of austenitic and super austenitic stainless steels at high temperatures
D Ahmed, M Mulapeer - Zanco Journal of Pure and Applied Sciences, 2022 - iasj.net
Due to the relatively high wear rate of the austenitic stainless steel S30400 and the high
mechanical properties of the super austenitic stainless steel S31254, it was possible to …
mechanical properties of the super austenitic stainless steel S31254, it was possible to …
Effect of argon gas environment on high temperature sliding wear characteristics of NiCrBSi laser clad
The martensitic stainless steels find extensive application in steam turbine blades, marine
turbine blades, compressor blades etc. due to the optimum combination of strength and …
turbine blades, compressor blades etc. due to the optimum combination of strength and …
Densification behaviour and the effect of heat treatment on microstructure, and mechanical properties of sintered nickel-based alloys
N Kekana, MB Shongwe, OT Johnson… - The International Journal …, 2019 - Springer
The present work focused on the densification behaviour and heat treatment effect on the
mechanical properties of spark plasma sintered Ni–Fe–Al–Cr alloys. Five initial alloys were …
mechanical properties of spark plasma sintered Ni–Fe–Al–Cr alloys. Five initial alloys were …