Severe plastic deformation: Nanostructured materials, metal-based and polymer-based nanocomposites: A review
M Fattahi, CY Hsu, AO Ali, ZH Mahmoud, NP Dang… - Heliyon, 2023 - cell.com
Significant deformation of the metal structure can be achieved without breaking or cracking
the metal. There are several methods for deformation of metal plastics. The most important of …
the metal. There are several methods for deformation of metal plastics. The most important of …
Structure, biodegradation, and in vitro bioactivity of Zn–1% Mg alloy strengthened by high-pressure torsion
N Martynenko, N Anisimova, O Rybalchenko… - Materials, 2022 - mdpi.com
The effect of high-pressure torsion (HPT) on the microstructure, phase composition,
mechanical characteristics, degradation rate, and bioactive properties of the Zn–1% Mg …
mechanical characteristics, degradation rate, and bioactive properties of the Zn–1% Mg …
Surface modification and surface composites development techniques for biocompatible and biodegradable alloys
The degradation control of implants has now become a most critical factor for investigation.
The rapid degradation or uncontrolled degradation of metals causes allergic reaction and …
The rapid degradation or uncontrolled degradation of metals causes allergic reaction and …
An in-silico investigation of biomechanical response of cardiovascular stents during deployment inside a stenotic artery
M Rajabi, AR Eivani, SH Seydein… - Journal of Ultrafine …, 2024 - jufgnsm.ut.ac.ir
Three commercial stents (Palmaz-Schatz, NIR, and BioMatrix) with either an open-cell (20%
open-cell) or a closed-cell (80% closed-cell) design, and one new hybrid stent design were …
open-cell) or a closed-cell (80% closed-cell) design, and one new hybrid stent design were …
Микроструктура и свойства сплава Zn–1% Li–2% Mg, подвергнутого интенсивной пластической деформации. Frontier Materials & Technologies. 2023. № 2
ВД Ситдиков, ЭД Хафизова, МВ Поленок - DOI, 2023 - elpub.ru
Аннотация В данной работе рассматриваются механизмы формирования
высокопрочных состояний в сплаве Zn–1% Li–2% Mg в результате его обработки …
высокопрочных состояний в сплаве Zn–1% Li–2% Mg в результате его обработки …
An investigation on microstructures and residual stresses of pure copper sheets fabricated by constrained studded pressing
MM Kaykha, SS Hosseini Faregh - Journal of Ultrafine Grained and …, 2024 - jufgnsm.ut.ac.ir
One of the newest methods of severe plastic deformation (SPD) is Constrained studded
pressing (CSP) method. A limitation of the constrained studded pressing process is the …
pressing (CSP) method. A limitation of the constrained studded pressing process is the …
Microstructure and properties of the Zn–1% Li–2% Mg alloy subjected to severe plastic deformation
VD Sitdikov, ED Khafizova… - Frontier Materials & …, 2023 - vektornaukitech.ru
In this paper, the authors consider the mechanisms of formation of high-strength states in the
Zn–1% Li–2% Mg alloy as a result of its processing by the high pressure torsion (HPT) …
Zn–1% Li–2% Mg alloy as a result of its processing by the high pressure torsion (HPT) …
FRONTIER MATERIALS & TECHNOLOGIES
ВД Ситдиков, ОБ Кулясова, ГФ СИТДИКОВА… - FRONTIER MATERIALS & … - elibrary.ru
В данной работе рассматриваются механизмы формирования высокопрочных
состояний в сплаве Zn-1% Li-2% Mg в результате его обработки методом интенсивной …
состояний в сплаве Zn-1% Li-2% Mg в результате его обработки методом интенсивной …