A review of studies in the field of production of coatings on metals by means of mechanical alloying
RA Savrai, AN Morozova - Surfaces and Interfaces, 2021 - Elsevier
The mechanical alloying method is widely used for production of powdered alloys. However,
focused studies have shown that this method may also be used for deposition of coatings …
focused studies have shown that this method may also be used for deposition of coatings …
High temperature cyclic oxidation resistance of 50Cr-50Al coatings mechanically alloyed on low carbon steel
In the present study, the 50Cr-50Al coatings were mechanically alloyed on low carbon steel
at two different milling times of 1 h and 4 h, and subsequently annealed in vacuum at 800° C …
at two different milling times of 1 h and 4 h, and subsequently annealed in vacuum at 800° C …
[PDF][PDF] Hydraulic fracturing candidate-well selection using artificial intelligence approach
A Aryanto, S Kasmungin… - Prosiding seminar …, 2018 - e-journal.trisakti.ac.id
Hydraulic fracturing is one of the stimulation method that aimed to increaseproductivity of
well by creating a high conductive conduit in reservoir connecting it to thewellbore. This high …
well by creating a high conductive conduit in reservoir connecting it to thewellbore. This high …
Microstructure and phase composition of Fe-B-Al coatings on low carbon steel prepared by using mechanical alloying technique
RY Sundawa, D Aryanto… - Journal of Physics …, 2017 - iopscience.iop.org
In the present study, varying composition of FeB-Al was coated on low carbon steel by using
mechanical alloying technique for 4 hours and followed by heat treatment in vacuum …
mechanical alloying technique for 4 hours and followed by heat treatment in vacuum …
High temperature oxidation of Fe-Cr-Al coatings prepared by flame spray technique
AE Fath, D Aryanto, SA Saptari… - Journal of Physics …, 2019 - iopscience.iop.org
In the present study, Fe-Cr and (Fe-Cr)-30at% Al coatings were prepared by a flame spray
technique. The coated samples were then annealed in a vacuum furnace at 800 C for 2h …
technique. The coated samples were then annealed in a vacuum furnace at 800 C for 2h …
The effect of annealing on structure and hardness of (Fe-Cr)-50 at.% Al coatings synthesized by mechanical alloying
C Ciswandi, D Aryanto, I Irmaniar, A Tjahjono… - AIP Conference …, 2018 - pubs.aip.org
In this research, the deposition of (Fe-Cr)-50at.% Al coatings on low carbon steel was
carried out by a mechanical alloying (MA) technique. The MA was performed in a shaker mill …
carried out by a mechanical alloying (MA) technique. The MA was performed in a shaker mill …
[PDF][PDF] Karakterisasi Struktur Coating Fe-25Al Yang Difabrikasi Dengan Metode Paduan Mekanik [Structure Characterization of Fe-25Al Coating Fabricated by …
Fe-25Al coating has been prepared on low carbon steel substrate by using a mechanical
alloying technique. Structure of Fe-25Al coating before and after heat treatment at 600, 700 …
alloying technique. Structure of Fe-25Al coating before and after heat treatment at 600, 700 …
Correlations between Structural and Hardness of Fe-50% Al Coating Prepared by Mechanical Alloying
Fe-50% Al coatings were deposited on the surface of low-carbon steel using mechanical
alloying technique atdifferent milling times. The correlation between structure and hardness …
alloying technique atdifferent milling times. The correlation between structure and hardness …
[PDF][PDF] Structure and Oxidation Resistance of Flamesprayed Fe–Ni–Al Coating
TS Saptari - researchgate.net
Two types of Fe–Ni–Al coatings as Fe75Ni15Al10 and Fe56Ni14Al30 were successfully
deposited on the surface of low carbon steel using the flamespray technique. Coated …
deposited on the surface of low carbon steel using the flamespray technique. Coated …
Structure and Oxidation Resistance of Flamesprayed Fe–Ni–Al Coating
ASI Datu-Maki, B Hermanto, SA Saptari… - Journal of Physics …, 2019 - iopscience.iop.org
Abstract Two types of Fe-Ni-Al coatings as Fe 75 Ni 15 Al 10 and Fe 56 Ni 14 Al 30 were
successfully deposited on the surface of low carbon steel using the flamespray technique …
successfully deposited on the surface of low carbon steel using the flamespray technique …