Compressive properties of imperfect Ti-6Al-4V lattice structure fabricated by electron beam powder bed fusion under static and dynamic loadings
Mechanical response and deformation behavior of Ti-6Al-4V lattice structure are
investigated by quasi-static and low-speed impact compression experiments. The lattice …
investigated by quasi-static and low-speed impact compression experiments. The lattice …
Quasi-static and dynamic behavior of additively manufactured metamaterial structures with layered-hybrid topologies
X Wang, R Qin, X Zhang, B Chen - Thin-Walled Structures, 2023 - Elsevier
A layered-hybrid metamaterial structure (LHMS) composed of a bio-inspired lattice cell and
a dodecagon body-centered lattice cell is proposed, for the purpose of combining the …
a dodecagon body-centered lattice cell is proposed, for the purpose of combining the …
Mechanical characteristic comparison of additively manufactured Ti–6Al–4V lattice structures in biocompatible bone tissue growth
SF Tseng, IH Wang, CM Chang, CC Lee… - Materials Science and …, 2022 - Elsevier
This study proposed the development of Ti–6Al–4V lattice structures suitable for the growth
of bone cells using laser powder bed fusion (PBF) and heat treatment of vacuum furnace …
of bone cells using laser powder bed fusion (PBF) and heat treatment of vacuum furnace …
[HTML][HTML] Analysis of the influence of L-PBF porosity on the mechanical behavior of AlSi10Mg by XRCT-based FEM
A Pascual, N Ortega, S Plaza, LNL de Lacalle… - journal of materials …, 2023 - Elsevier
This work aims to present an XRCT-based FEM methodology to assess the influence of
porosity defects on the mechanical behavior and failure of L-PBF AlSi10Mg components …
porosity defects on the mechanical behavior and failure of L-PBF AlSi10Mg components …
[HTML][HTML] Experimental investigation and numerical modeling of laser powder bed fusion process-induced angle-dependent defects in strut-based lattice structure
The emergence of additive manufacturing technology has enabled the fabrication of
advanced structures with intricate geometric topologies. However, additive manufacturing …
advanced structures with intricate geometric topologies. However, additive manufacturing …
Determination of cell size/structures and mechanical properties of additively manufactured metallic components using X-ray technique
K Moj, R Owsiński, G Robak, MK Gupta - Rapid Prototyping Journal, 2023 - emerald.com
Purpose Additive manufacturing (AM), a rapidly evolving paradigm, has shown significant
advantages over traditional subtractive processing routines by allowing for the custom …
advantages over traditional subtractive processing routines by allowing for the custom …
Cyclic behaviour modelling of additively manufactured Ti-6Al-4V lattice structures
M Doroszko, A Seweryn - International Journal of Mechanical Sciences, 2024 - Elsevier
The present work is concerned with the numerical modelling of the cyclic behaviour of Ti-6Al-
4V lattice structures. In the study, diamond structures of titanium alloy produced by the …
4V lattice structures. In the study, diamond structures of titanium alloy produced by the …
XCT-assisted micromechanical modeling of the effect of pores on the plastic deformation and mechanical characteristics of PBF-LB/M-produced copper alloys
Due to the low absorption of fiber laser by copper particles, the laser-based powder bed
fusion (PBF-LB/M) processing of copper components is accompanied by the development of …
fusion (PBF-LB/M) processing of copper components is accompanied by the development of …
[HTML][HTML] Structural optimization design and compression performance of porous titanium prepared by laser powder bed fusion
Y Hu, H Li, H Chen, S Zhang, Z Wang, J Lei - Journal of Materials Research …, 2024 - Elsevier
Porous implants composed of periodically-repeating porous units have been applied in
orthopedic surgeries to replace damaged bones. An important requirement for bone …
orthopedic surgeries to replace damaged bones. An important requirement for bone …
Numerical Investigation of the Defects Effect in Additive Manufactured Ti-6Al-4V Struts on Deformation Behavior Based on Microtomographic Images
M Doroszko - Materials, 2022 - mdpi.com
This paper describes the influence of defects occurring in struts under tension, obtained
using the additive method of laser powder bed fusion (LPBF), on the stress and strain …
using the additive method of laser powder bed fusion (LPBF), on the stress and strain …