Effects of heat input and martensite on HAZ softening in laser welding of dual phase steels
Laser welds were made in three dual-phase (DP) alloys with ultimate tensile strengths
ranging from 450–980 MPa and varying microstructures to investigate effects of heat input …
ranging from 450–980 MPa and varying microstructures to investigate effects of heat input …
Effect of annealing atmosphere on the galvanizing behavior of a dual-phase steel
R Khondker, A Mertens, JR McDermid - Materials Science and Engineering …, 2007 - Elsevier
The influence of annealing atmosphere oxidation potential (ie pH2O/pH2 ratio) on the
surface condition of an industrial dual-phase steel alloyed with 2wt.% Mn and 0.3 wt.% Mo …
surface condition of an industrial dual-phase steel alloyed with 2wt.% Mn and 0.3 wt.% Mo …
Microstructure-properties correlation in fiber laser welding of dual-phase and HSLA steels
Similar and dissimilar welds of dual-phase (DP) and high strength low alloy (HSLA) steels
were made by fiber laser welding (FLW). The welds were characterized with respect to …
were made by fiber laser welding (FLW). The welds were characterized with respect to …
Effects of weld line position and geometry on the formability of laser welded high strength low alloy and dual-phase steel blanks
Formability of laser welded blanks (LWBs) was measured in the biaxial stretch forming mode
using the limiting dome height (LDH) test. High strength low alloy steel and two dual-phase …
using the limiting dome height (LDH) test. High strength low alloy steel and two dual-phase …
Microstructure, hardness and tensile properties of fusion zone in laser welding of advanced high strength steels
A Santillan Esquivel, SS Nayak, MS Xia… - Canadian Metallurgical …, 2012 - Taylor & Francis
Fusion zone (FZ) of advanced high strength steel welds, with similar and dissimilar
combinations, in diode laser welding was characterised in respect to microstructure …
combinations, in diode laser welding was characterised in respect to microstructure …
[HTML][HTML] Liquid Metal Embrittlement Susceptibility and Crack Formation of the Zn-Coated Complex Phase Steel
R Hu, J Zhou, Y Sun, M Lei, Y Gao - Materials, 2024 - mdpi.com
In the resistance spot-welding (RSW) of galvanized complex phase (CP) steel, liquid metal
embrittlement (LME) may occur, deteriorating the welded joint's performance. Based on the …
embrittlement (LME) may occur, deteriorating the welded joint's performance. Based on the …
A fabrication history based strain‐fatigue model for prediction of crack initiation in a radial loading wheel
Y Zhao, M Ma, R Qin, Y Ling, G Wang… - Fatigue & Fracture of …, 2017 - Wiley Online Library
A strain‐based fatigue model concerning fabrication history is applied to predict the fatigue
life of a commercial car wheel under radial loads. As the prior conditions, the strain fatigue …
life of a commercial car wheel under radial loads. As the prior conditions, the strain fatigue …
The effect of weld design on the formability of laser tailor welded blanks
J Li - 2010 - uwspace.uwaterloo.ca
Tailor welded blanks (TWBs) are used in the automotive industries as a method to meet
economic, environmental and governmental demands. Conventionally, TWBs incorporated …
economic, environmental and governmental demands. Conventionally, TWBs incorporated …
双相钢点焊熔核界面撕裂失效模式评价
杨海军， 张延松， 来新民， 张小云 - 焊接学报, 2011 - hjxb.hwi.com.cn
双相钢点焊熔核中大量的相变马氏体, 导致熔核脆性增加, 其界面撕裂问题严重降低了焊点的
力学性能, 导致接头质量下降. 采用传统的评价标准会产生焊点界面撕裂问题 …
力学性能, 导致接头质量下降. 采用传统的评价标准会产生焊点界面撕裂问题 …
变形温度对含Nb 双相钢显微组织的影响
董毅， 许云波， 吴迪 - 金属学报, 2009 - jcscp.org
通过单道次压缩及连续冷却实验, 研究了变形温度(810-720℃) 对具有超细原始奥氏体晶粒的含
Nb 双相钢显微组织的影响. 实验结果表明: 实验钢最终组织为铁素体加马氏体的双相组织 …
Nb 双相钢显微组织的影响. 实验结果表明: 实验钢最终组织为铁素体加马氏体的双相组织 …