Study of anisotropy through microscopy, internal friction and electrical resistivity measurements of Ti-6Al-4V samples fabricated by selective laser melting
A Nespoli, N Bennato, E Villa… - Rapid Prototyping Journal, 2022 - emerald.com
Purpose This paper aims to investigate the microstructural anisotropy of Ti-6Al-4V samples
fabricated by selective laser melting. Design/methodology/approach Specimens are …
fabricated by selective laser melting. Design/methodology/approach Specimens are …
Strain-rate-dependent deformation behavior in a Ti-based bulk metallic glass composite upon dynamic deformation
J Bai, JS Li, J Wang, J Cui, LY Li, HC Kou… - Journal of Alloys and …, 2015 - Elsevier
The deformation behavior of in-situ Ti 48 Zr 20 Nb 12 Cu 5 Be 15 bulk-metallic-glass (BMG)
composites was investigated upon dynamic deformation. The present BMG composite …
composites was investigated upon dynamic deformation. The present BMG composite …
Cryogenic-and ultrasonic-induced local martensite-like order in Cu47. 5Zr45. 5Al5Er2 bulk metallic glasses
A Moreno-Gobbi, PS Silva Jr, A Maso… - Materials Today …, 2021 - Elsevier
This study analyzed the influence of low-temperature elastic ultrasonic stimulus on the local
structural order of Cu 47.5 Zr 45.5 Al 5 Er 2 amorphous alloy, using the ultrasonic pulse …
structural order of Cu 47.5 Zr 45.5 Al 5 Er 2 amorphous alloy, using the ultrasonic pulse …
Elastic stress induced metastable local ordering in Cu-Zr-Al metallic glasses: a numerical simulation study
This work presents a study based on numerical simulations to describe the local structural
evolution of Cu-Zr-Al amorphous alloys when moderate stresses are applied and removed …
evolution of Cu-Zr-Al amorphous alloys when moderate stresses are applied and removed …
Relaxation of Ni-free Ti40Zr10Cu36Pd14 bulk metallic glass under mechanical stress
JC Qiao, Q Wang, JM Pelletier, Y Yao - Intermetallics, 2018 - Elsevier
Dynamic mechanical behavior of Ti 40 Zr 10 Cu 36 Pd 14 bulk metallic glass was
investigated by mechanical spectroscopy. The mechanical spectra of Ti 40 Zr 10 Cu 36 Pd …
investigated by mechanical spectroscopy. The mechanical spectra of Ti 40 Zr 10 Cu 36 Pd …
Investigation by mechanical spectroscopy at different frequencies of the nucleation processes in amorphous Cu-Zr-Al alloys
PWB Marques, O Florêncio, PS Silva Jr… - Materials Science and …, 2017 - Elsevier
The anelastic spectra of Cu 39.5 Zr 51 Al 9.5, Cu 54 Zr 40 Al 6 and Cu 47.75 Zr 47.75 Al 4.5
bulk metallic glasses were obtained by Mechanical Spectroscopy Technique at different …
bulk metallic glasses were obtained by Mechanical Spectroscopy Technique at different …
Peculiarities of ball-milling induced crystalline–amorphous transformation in Cu–Zr–Al–Ni–Ti alloys
An amorphization process in (Cu 49 Zr 45− x Al 6+ x) 100− y− z Ni y Ti z (x= 1, y, z= 0; 5; 10)
induced by ball-milling is reported in the present work. The aim was investigation of the …
induced by ball-milling is reported in the present work. The aim was investigation of the …
Synthesis and characterization of copper-based composites reinforced by CuZrAlNiTi amorphous particles with enhanced mechanical properties
Novel amorphous/crystalline composites were developed combining the ductile copper
matrix with hard CuZr-based amorphous powder. The amorphous powders of two …
matrix with hard CuZr-based amorphous powder. The amorphous powders of two …
Ultrasonic study of polycrystalline Ti–40Nb alloys at cryogenic temperatures
AOM Gobbi, DRN Correa, PSS Junior, RFM dos Santos… - MRS Advances, 2024 - Springer
Ultrasonic velocity and attenuation measurements of hot-forged β-type Ti–40Nb (% wt) alloy
were realized in cooling–heating cycles between 130 and 300 K. The anelastic spectra …
were realized in cooling–heating cycles between 130 and 300 K. The anelastic spectra …