Focused review on Cu–Ni–Sn spinodal alloys: from casting to additive manufacturing
The present review article evaluates the research and progress status of Cu–Ni–Sn-based
spinodal alloys focussed on the methods and technologies implemented to enhance the …
spinodal alloys focussed on the methods and technologies implemented to enhance the …
Design of heterogeneous structured Al alloys with wide processing window for laser-powder bed fusion additive manufacturing
Required microstructural attributes of an alloy vary with structural applications. The
microstructural fine-tuning capability of laser-powder bed fusion (L-PBF) additive …
microstructural fine-tuning capability of laser-powder bed fusion (L-PBF) additive …
Constitutive modeling of cellular-structured metals produced by additive manufacturing
Computational modeling is essential in the development and application of metal additive
manufacturing (MAM). Most materials processed by laser or electron beam MAM exhibit a …
manufacturing (MAM). Most materials processed by laser or electron beam MAM exhibit a …
[HTML][HTML] Outstanding strengthening behavior and dynamic mechanical properties of in-situ Al–Al3Ni composites by Cu addition
The microstructure, mechanical properties, and dynamic mechanical properties of the
various intermetallic-reinforced in-situ Al–Al 3 Ni eutectic composites were investigated for …
various intermetallic-reinforced in-situ Al–Al 3 Ni eutectic composites were investigated for …
Microstructure features and mechanical/electrochemical behavior of directionally solidified Al− 6wt.% Cu− 5wt.% Ni alloy
The effects of the addition of 5.0 wt.% Ni to an Al− 6wt.% Cu alloy on the solidification
cooling rate T˙ growth rate (VL), length scale of the representative phase of the …
cooling rate T˙ growth rate (VL), length scale of the representative phase of the …
Transient directional solidification of a eutectic Al–Si–Ni alloy: Macrostructure, microstructure, dendritic growth and hardness
Abstract The Al-11 wt% Si-5 wt% Ni eutectic alloy was directionally solidified (DS) under
transient heat flow conditions at cooling rates in a range of about 1–25° C/s along the length …
transient heat flow conditions at cooling rates in a range of about 1–25° C/s along the length …
Microstructure and hardness of laser remelted surfaces of Al-5% Cu and Al-4% Cu-1% Ni alloys
AF Schon, GL de Gouveia, BS Sobral… - Journal of Alloys and …, 2023 - Elsevier
Al-based alloys are potential candidates for advanced rapid solidification processes, such
as Laser Surface Remelting (LSR) and Additive Manufacturing (AM). However, currently few …
as Laser Surface Remelting (LSR) and Additive Manufacturing (AM). However, currently few …
Effect of V on high-temperature mechanical properties of Al–5Cu–1.5 Ni alloy
J Cui, Y Chen, X Fu, H Yang, H Wang, A Li… - Journal of Iron and Steel …, 2024 - Springer
The effects of V on microstructure, room temperature, and high-temperature (350° C)
mechanical properties of Al–5Cu–1.5 Ni alloy were investigated. The results show that Al …
mechanical properties of Al–5Cu–1.5 Ni alloy were investigated. The results show that Al …
[HTML][HTML] Corrosion behavior of an Al–Sn–Zn alloy: Effects of solidification microstructure characteristics
Due to its strong influence on service life of manufactured parts, corrosion resistance is an
important factor to consider when designing Al alloys for engineering applications. With this …
important factor to consider when designing Al alloys for engineering applications. With this …
Tailoring of processing parameters, dendritic microstructure, Si/intermetallic particles and microhardness in as-cast and heat-treated samples of Al7Si0. 3Mg alloy
CR Barbosa, GH Machado, HM Azevedo… - Metals and Materials …, 2020 - Springer
In this work, solidification and T6-heat treatment experiments were performed with the
Al7Si0. 3Mg alloy in order to investigate the effect of processes parameters on the …
Al7Si0. 3Mg alloy in order to investigate the effect of processes parameters on the …