A review of advances in tribology in 2020–2021
Y Meng, J Xu, L Ma, Z Jin, B Prakash, T Ma, W Wang - Friction, 2022 - Springer
Abstract Around 1,000 peer-reviewed papers were selected from 3,450 articles published
during 2020–2021, and reviewed as the representative advances in tribology research …
during 2020–2021, and reviewed as the representative advances in tribology research …
[HTML][HTML] An insight into the effect of rough surfaces and contact orientation on the fretting characteristics of quenched and tempered steel
The effect of a rough, textured surface and contact orientations on the fretting behavior of self-
mated martensitic 34CrNiMo6+ QT steel was examined via a large annular flat-on-flat …
mated martensitic 34CrNiMo6+ QT steel was examined via a large annular flat-on-flat …
Fretting fatigue of 42CrMo4+ QT steel: Experimental and numerical assessment
M Nesládek, JME Marques, J Papuga, F Fojtík… - International Journal of …, 2024 - Elsevier
This paper focuses on an experimental and numerical assessment of fretting fatigue in
cyclically loaded specimens from 42CrMo4+ QT steel in contact with bridge pads of the …
cyclically loaded specimens from 42CrMo4+ QT steel in contact with bridge pads of the …
[HTML][HTML] Influence of displacement amplitude on fretting-induced friction and wear of steel in oil-lubricated contact
A Zabihi, J Juoksukangas, J Hintikka, T Salminen… - Tribology …, 2024 - Elsevier
Many fretting-prone contacts are surrounded by oils, although they are not intended to
lubricate them. To study the fretting behavior of contacts whose edge is exposed to engine …
lubricate them. To study the fretting behavior of contacts whose edge is exposed to engine …
Wear of TiAlCN Coating on HCR Gear
P Švec, Ľ Magdolen, R Protasov, M Bošanský… - Lubricants, 2022 - mdpi.com
Wear of TiAlCN coatings deposited on HCR (High Contact Ratio) gears was studied by the
Niemann test during which the tested gears were loaded up to the 12th load stage. The …
Niemann test during which the tested gears were loaded up to the 12th load stage. The …
ASSESSMENT OF THE CONDITION OF THE FINISH-ROLLED SHAFT TOP LAYER FOR FRETTING WEAR DEVELOPMENT.
S Kowalski - Journal of the Balkan Tribological Association, 2021 - search.ebscohost.com
The tribological kinematic pair, which was subjected to wear tests, consists of a finish-rolled
shaft and a sleeve joined with the shaft by forcing, where the tolerance was 0.02 mm. Both …
shaft and a sleeve joined with the shaft by forcing, where the tolerance was 0.02 mm. Both …
[PDF][PDF] Commissioning and preliminary testing of a fretting test device
R Kovanen - 2022 - trepo.tuni.fi
Fretting is low amplitude reciprocating sliding that may occur in nominally static contacts. It
results in surface damage through fretting wear where mechanical wear and surface fatigue …
results in surface damage through fretting wear where mechanical wear and surface fatigue …
Investigating the Impact of Monolayer and Multilayer PVD Coatings on Cutting Tool Friction Factor
K Paulian, V Manickam, V Tharanipathy - 2024 - researchsquare.com
The purpose of the paper is to examine the ZrSiN, monolayer TiN, and multilayer TiSiN PVD
coatings' friction factors on tempered steel 45X (50 HRC) and steel 45 (180 HB). The …
coatings' friction factors on tempered steel 45X (50 HRC) and steel 45 (180 HB). The …
[PDF][PDF] Wear of TiAlCN Coating on HCR Gear. Lubricants 2022, 10, 342
P Švec, L Magdolen, R Protasov, M Bošanský… - 2022 - academia.edu
Wear of TiAlCN coatings deposited on HCR (High Contact Ratio) gears was studied by the
Niemann test during which the tested gears were loaded up to the 12th load stage. The …
Niemann test during which the tested gears were loaded up to the 12th load stage. The …