Mixing of carbon nanotubes (CNTs) and aluminum powder for powder metallurgy use
J Liao, MJ Tan - Powder technology, 2011 - Elsevier
In recent years, carbon nanotubes (CNTs) reinforced aluminum matrix composites (AMCs)
have attracted increasing attention. The quality of dispersion, however, is a crucial factor …
have attracted increasing attention. The quality of dispersion, however, is a crucial factor …
Metal injection moulding of CP-Ti components for biomedical applications
AT Sidambe, IA Figueroa, HGC Hamilton… - Journal of Materials …, 2012 - Elsevier
Titanium exhibits properties that are excellent for various applications but the processing
routes remain expensive and difficult. Metal injection moulding is a processing route that …
routes remain expensive and difficult. Metal injection moulding is a processing route that …
A novel water leaching and sintering process for manufacturing highly porous stainless steel
HI Bakan - Scripta materialia, 2006 - Elsevier
Highly porous 316L stainless steel samples with 70vol.% porosity were manufactured using
water leaching and sintering methods. Irregular carbamide powders were used as a space …
water leaching and sintering methods. Irregular carbamide powders were used as a space …
[HTML][HTML] High-capacity Li4Ti5O12-C thick ceramic electrodes manufactured by powder injection moulding
I Romero-Garcia, ME Sotomayor, B Levenfeld… - Journal of the European …, 2024 - Elsevier
Lithium-ion batteries are the most efficient electrochemical energy storage devices.
However, there is still room for improvement in terms of safety and energy density, presently …
However, there is still room for improvement in terms of safety and energy density, presently …
Powder injection moulding of premixed ferritic and austenitic stainless steel powders
ME Sotomayor, B Levenfeld, A Várez - Materials Science and Engineering …, 2011 - Elsevier
In this experimental work, powder injection moulding (PIM) of premixed 316L and 430L gas-
atomized powders was developed to obtain duplex stainless steels. A multicomponent …
atomized powders was developed to obtain duplex stainless steels. A multicomponent …
[PDF][PDF] Metal injection moulding of Ti-64 components using a water soluble binder
Titanium and titanium alloys exhibit a high specific strength and stiffness, outstanding
corrosion resistance and biocompatibility. This combination of properties makes titanium …
corrosion resistance and biocompatibility. This combination of properties makes titanium …
The bonding of nickel foam to Ti–6Al–4V using Ti–Cu–Ni braze alloy
T Jarvis, W Voice, R Goodall - Materials Science and Engineering: A, 2011 - Elsevier
A titanium-copper-nickel braze powder is combined with various carrier polymers at a range
of loadings and used to braze open cell nickel foams to Ti–6Al–4V plate. The microstructure …
of loadings and used to braze open cell nickel foams to Ti–6Al–4V plate. The microstructure …
Optimization of binder removal for ceramic microfabrication via polymer co-extrusion
The objective of this study is to assess the feasibility of solvent extraction (SE) for partial
binder removal in the context of polymer co-extrusion with a thermoplastic binder …
binder removal in the context of polymer co-extrusion with a thermoplastic binder …
Fabrication of ZrO2–CoAl2O4 Composite by Injection Molding and Solution Infiltration
G Liu, Z Xie, W Wang, Y Wu - International Journal of Applied …, 2011 - Wiley Online Library
ZrO2–CoAl2O4 composite was fabricated via infiltrating solvent debound injection‐molded
green body. The technique used consists of the following steps: ceramic injection molding to …
green body. The technique used consists of the following steps: ceramic injection molding to …
低碳钢中铁素体动态再结晶的粒子激发形核
王猛， 李龙飞， 杨王玥， 孙祖庆 - 工程科学学报, 2008 - cje.ustb.edu.cn
利用淬, 回火工艺得到具有弥散分布的渗碳体粒子+ 铁素体双相组织的低碳钢, 采用Gleeble-
1500 型模拟机进行热压缩变形实验, 研究了在700℃, 0.01 s-1 条件下变形过程中渗碳体粒子对 …
1500 型模拟机进行热压缩变形实验, 研究了在700℃, 0.01 s-1 条件下变形过程中渗碳体粒子对 …